Noise analysis of continuous GPS coordinate time series for CMONOC

The Crustal Movement Observation Network of China (CMONOC) is one of the major scientific infrastructures, mainly using Global Positioning System (GPS) measurements, to monitor crustal deformation in the Chinese mainland. In this paper, decade-long coordinate time series of 26 continuous GPS sites of CMONOC are analyzed for their noise content using maximum likelihood estimation (MLE). We study the noise properties of continuous GPS time series of CMONOC for the unfiltered, filtered solutions and also the common mode signals in terms of power law plus white noise model. In the spatial filtering, we remove for every time series a common mode error that was estimated from a modified stacking of position residuals from other sites within ∼1000 km of the selected site. We find that the common mode signal in our network has a combination of spatially correlated flicker noise and a common white noise with large spatial extent. We demonstrate that for the unfiltered solutions of CMONOC continuous GPS sites the main colored noise is a flicker process, with a mean spectral index of ∼1. For the filtered solutions, the main colored noise is a general power law process, indicating that a major number of the filtered regional solutions have a combination of noise sources or local effects. The velocity uncertainties from CMONOC continuous GPS coordinate time series may be underestimated by factors of 8–16 if a pure white noise model is assumed. In addition, using a white plus flicker noise model, the median values of velocity errors for the unfiltered solutions are 0.16 (north), 0.17 (east) and 0.58 (vertical) mm/yr, and the median values for the filtered solutions are 0.09 (north), 0.10 (east) and 0.40 (vertical) mm/yr.     

协同翻译环境下辅助译文生成技术研究

在协同翻译过程中，辅助译文的质量是影响协同翻译效率的重要因素，而现有辅助译文生成方法并没有考虑用户对辅助译文的个性化需求。由此，提出了通过建立用户模型来提高辅助译文质量的研究思路，根据翻译知识库与用户知识库的相对熵的大小来决策为用户提供哪个模板。实验表明：在使用用户模型后，协同翻译的效率有了明显的提高。     

某类跨大气层飞行器全航程红外辐射特性分析

针对某类跨大气层飞行器飞行过程中需要进出大气层,且飞行速度跨度大等特点,建立了不同空域、不同飞行速度下的机体头部受热模型。当在大气层内飞行时分别使用经验公式和Lees公式计算马赫数小于5和大于5时头部受热情况,当在大气层外飞行时建立了考虑太阳直射、地球反照和地球红外加热情况下的受热模型。利用普朗克定律得到了相同温度下不同波段的红外辐射能量占比情况。最后利用本文方法对某类跨大气层飞行器进行了温度和红外辐射计算,得到的计算结果能够大致反映全航程头部温度和红外辐射变化情况。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

CFRP钻削过程的切削热研究进展

以CFRP钻削加工过程的切削热和切削温度为研究对象,从其形成机理、产生的影响以及影响切削热的因素和控制切削热的方法四个方面进行了系统综述,对存在的问题进行了综合分析,并对今后研究方向进行了展望。     

高湍流度时全气膜涡轮叶片表面冷却和换热特性的实验研究

为获得高主流湍流度时全气膜涡轮叶片表面的冷却和换热特性,在跨声速风洞中实验研究了质量流量比(MFR)和主流雷诺数(Re)对叶片表面气膜冷却效率和换热系数比的影响。在叶片前缘布置了5排圆形孔,在吸力面和压力面分别布置了3排和6排圆形孔,实验结果由嵌入在叶片中截面的热电偶测得。实验中基于弦长的主流雷诺数的范围为3.0×105～9.0×105,叶栅出口马赫数Ma为0.8, MFR的范围是5.5%～12.5%,主流湍流度Tu为14.7%。实验结果表明:主流雷诺数升高显著增强了叶片表面的换热,使层流边界层到湍流边界层的转捩位置提前。对于吸力面S/C0.2的区域(S/C为当地弧长与弦长之比),气膜冷却效率受MFR影响明显,当MFR大于7.7%时提高MFR会导致气膜冷却效率降低;该区域的换热系数比在中低雷诺数时受MFR影响较小,在高雷诺数时随MFR升高而升高。压力面S/C-0.7区域的气膜冷却效率随MFR升高而升高,-0.7S/C-0.4区域的气膜冷却效率受MFR影响较小,对于整个压力面而言,MFR升高提高了叶片表面的换热系数。相对于叶片其它区域,压力面后半段区域和吸力面的气膜冷却效率受雷诺数影响较大。     

中心支板式RBCC发动机引射模态流动与燃烧研究

为了深入认识引射模态工作机理,针对中心支板式RBCC发动机,在飞行马赫数2、不同内置火箭流量时的工作情况进行了全流道一体化的数值模拟,并对其内流场特征、火箭射流/引射空气掺混发展特征以及复合型释热规律和火焰结构等开展了详细分析。研究发现:RBCC发动机引射模态下的流动掺混燃烧过程是一个复杂且高度耦合的过程。在即时预混燃烧(SMC)模式下,燃烧过程主要在内置火箭射流与来流空气之间形成的剪切层内进行;流道上游剪切层厚度较薄,温度和组分浓度梯度较大,掺混速率快;高释热区集中分布在流道上游,可分为超声速释热区和亚声速释热区;流道内的燃烧反应以扩散燃烧为主,随着掺混过程的进行逐渐向预混燃烧过渡。提高火箭流量,流道内温度升高,反应持续距离增加,但掺混效率降低。